Resistance
Resistance is one of three basic quantities in electrical or electronic circuits:
Current is the flow of electrons through a circuit. It is the principle quantity because it does work, and accomplishes the desired results. We measure current in Amperes. (See “UNITS”)
Voltage is the force that causes current to flow in a circuit. In fact, we sometimes call voltage “electromotive force” or “EMF.” We measure it in Volts.
Resistance controls the flow of current. We measure it in Ohms.
These three quantities are so basic to electrical and electronic circuits, a simple equation called Ohms Law relates them. Ohms law states that the current flowing in a circuit is proportional to the voltage applied to the circuit and inversely proportional to the resistance of the circuit. In other words, for a given voltage, the current in the circuit will decrease as the resistance increases.
Mathematically, Ohms Law is: I = E/R, or current equals voltage divided by resistance. This simple equation can be transformed to find voltage or resistance, given the other two quantities. (For example, if you know the voltage and current in a circuit, you can calculate the circuit resistance by dividing the voltage by the current.)
Ohms Law is truly fundamental. Every electrical or electronic circuit design begins here!
Conductors and Insulators
All materials are either conductors or insulators; a material will either conduct electrical current, or impede its flow.
Not all conductors are equally capable of supporting current flow. Copper is a better conductor than nickel. Silver is a better conductor than copper. Gold is a better conductor than Silver. Carbon is a poor conductor.
Similarly, insulators are not perfect. Wood is an insulator if dry, but becomes a conductor when wet. The best insulators are glasses and ceramics. Plastics, such as epoxy, are generally good insulators.
There also are materials that are neither conductors nor insulators. Called “semiconductors,” they are used to make transistors. We will not discuss transistors here, but it is interesting that they are really the only resistors that electronic circuits can control. This again shows that Ohms Law is fundamental to circuit design.
Resistors
There are several ways to make resistors for electrical or electronic circuits. Carbon resistors are made by attaching leads to a bar or rod of carbon material.
The material is usually made by suspending carbon particles in a plastic material. The material mix determines resistance.
Carbon resistors have some serious limitations. They cannot dissipate much power, and are difficult to make with small resistance tolerances. However, automated manufacturing makes them in large quantities, so their cost is low.
Some resistors are made with metal films or oxides. These resistors are small and can be manufactured with good tolerances. But, they cannot handle higher power levels. Another type of film resistor is made with conductive inks. They are inexpensive, but are unstable and have limited power dissipation and poor resistance tolerances.
Wirewound resistors are made by winding a length of wire on an insulating core. They can dissipate large power levels compared to other types, and can be made with extremely tight resistance tolerances and controlled temperature characteristics.
Its length, cross-section area, and material determine the resistance of a wire. Copper is a good conductor, but has some resistance (to current flow.) A small diameter copper wire, 100 feet long, may have a resistance of a few ohms. However, a small diameter nickel alloy wire only one foot long may have a resistance of several thousand ohms.
Riedon makes wire wound resistors using wire of several metal alloys and sizes. The selection of wire depends on several factors. For example, a high resistance design would require a long copper wire and the resistor would be large. The same resistor could be made with a short length of nickel alloy wire, resulting in a much smaller device. However, when a high precision resistor is required, it is easier to trim resistance by removing a few inches of a low resistance wire, than by trimming millimeters of high resistance wire.
Power
We measure electrical power in Watts. In a resistive circuit, power is calculated by squaring the current and multiplying that value by the resistance (P = I x R). Wirewound resistors excel in higher power rating applications.
Because resistors impede the flow of current, they generate heat. If the resistor operates within its power rating, the heat is harmlessly dissipated into the surrounding environment. But, if we exceed the wattage rating, the resistor cannot dissipate the excess heat, and its temperature rises. The resistor
will fail, usually by acting as a fuse and breaking the circuit. If the resistor is used in a high-temperature environment, its power rating must be lowered, or “derated.”
Temperature Coefficient
In wirewound resistors, another selection factor is the temperature characteristic of the wire.
The resistance of all materials changes as their temperature changes. If the temperature is lowered, resistance (typically) declines. In fact, if cooled sufficiently, the material becomes a superconductor with no significant resistance. Increasing the temperature (typically) increases resistance.
The temperature coefficient of resistance (TCR) of wire or a resistor relates the change in resistance to the change in temperature. It is usually expressed as “parts per million per degree Centigrade” (ppm/°C.) The temperature coefficient of resistance tells you how much the resistance changes (ppm) if the temperature changes one degree Centigrade.
Inductance
There is another quantity that is similar to resistance. It is called reactance. Like resistance, we measure reactance in ohms, and it follows the rule of Ohms Law.
Reactance only occurs in electrical or electronic circuits if the current flow is changing rapidly. It is usually important in alternating current (AC) circuits where the current periodically changes direction and amplitude at some rate called frequency. However, reactance does not exist in direct current (DC) circuits where current flows in one direction and its amplitude is not changing rapidly.
Reactance occurs because all circuit elements have inductance and capacitance. In AC circuits, the capacitance of wire wound resistors is seldom large enough to be considered, so we will ignore it in this discussion. However, the inductance of wire wound resistors can be critical!
All conductors have some inductance. When the conductor is coiled, as it usually is in wire wound resistors, this inductance becomes larger. In AC circuits, inductance causes inductive reactance. Inductive reactance and resistance add, increasing the resistor’s value.
Inductive reactance increases as the frequency of the alternating current increases. For example, a resistor might have enough inductance to create one ohm of reactance at a frequency of 60Hz (cycles per second.) If we increase the frequency to 6,000Hz (an audio frequency), the reactance would increase to 100 ohms. Increasing the frequency to 6,000,000Hz (a radio frequency), increases the resistor’s reactance is 10,000 ohms.
Obviously, the inductance of wirewound resistors can be significant in AC circuits! When reactance is important in AC circuit applications, Riedon can wind the wire in a special way to eliminate or reduce the resistor’s inductance.
Units
Amperes: (“Amps”)
Milliamp = 1/1,000 amp
Microamp = 1/1,000,000 amp
Volts:
Millivolt = 1/1,000 volts
Microvolt = 1/1,000,000 volts
Ohms:
Kilo ohm (“K ohm” ) = 1,000 ohms
Megohm = 1,000,000 ohms